Being handy with tools is a very good thing but, the first question that every clueless guy asks is… “how the hell do I learn this stuff?!”
Oh, what to do? Watch hours of HGTV? Even though that could be interesting, I think not. Sometimes you learn this stuff from your dad, other times, you’re simply the only guy smart enough to read the instructions. Either way, knowing your way around a toolbox is a good thing. These five starter tips will help you around the house – and spur you on to learn more.
1. Restart Your Garbage Disposal
A broken garbage disposal is a huge headache. Sure, you might have gotten along fine before you had one, but those were the days that dishes took a year to do.
Before you begin, make sure you get under the sink and unplug the disposal itself (many sinks have an outlet underneath them, just open the door and look for it.). If you can’t find that, flip the circuit breaker that gives power to the disposal. Seriously, you can’t skip this step because, if for some reason it turns on while you’re removing any stuck-on food in there, you will regret it.
Once the power is off, look under the sink again and find a button underneath the cylinder that houses the disposal mechanism. This is the reset button. Push it. You should hear a click to let you know you’ve done it.
Next, see if you can locate any debris stuck inside the mouth of the disposal. This is when you need to be absolutely certain that no power is going to it. Remove everything you can.
Flip the power back on and check if it’s working. If so, congratulations. If not, there is still one last thing you can do: manually dislodge what’s keeping the blades stuck. For this method, you’ll need an Allen wrench/hex key. There is a small socket in the middle of the bottom of the disposal unit the key can fit into. Turn the key either way—this is essentially moving the grinders of the unit manually. Turn back and forth a couple times to ensure you got what was keeping the grinders stuck and try flipping the switch again. This should take care of it.
2. Stop A Running Toilet That Doesn’t Stop Running
That sound, that constant sound. My master bath toilet made it, yours probably does at some point as well. It’s a torturous sound that can keep a guy up at night. Sure, the severity varies, but a toilet’s importance can never be understated.
A constantly running toilet not only drives you nuts, it can waste money as well, (literally) flushing dollars down the drain and into the septic tank when your water bill shows up.
First things first: If your toilet is running, reach behind it and turn the water off (there’s usually a knob behind it that controls the flow).
Next, lift the top of the tank. More often than not, you’ll find that the flapper or the flush valve has a problem, leaving the tank constantly emptying into the toilet bowl.
The fix can range from a readjustment of the float and the arm (so the tank gets plugged) to a complete replacement of the tank’s interior parts, a fix that might run you $20. It’s mostly a snap-and-place fixture and you should be able to figure it out just by looking at it.
3. Hammer The Nail… Not Your Hand
There’s nothing like hammering a nail perfectly. There’s an art to it. Hitting the nail square on the head. The problem is, it might not happen all the time, just like the old adage suggests.
To lose your fear of bashing your fingertips while driving a nail into a hard material that requires some force, set the nail in place and hold it with pliers as you hammer away. If you don’t have pliers, a fine-toothed plastic comb works wonders, too. If you’re working with multiple nails in close proximity, you can also use it as a rudimentary straight edge as well. Plus, you can make sure your style stays perfect, it’s a win-win-win.
4. Fix a Clogged Drain
Perhaps one of the most frustrating things, a clogged drain can force you under the sink with a monkey wrench for a good part of a night. The trick here is to think strategically.
Many clogs can be fixed with liquid or gel drain cleaners, but if you’re facing something that’s got the whole thing backed up, get ready for a potentially messy fix.
First, you can try plunging it—yes, with the same tool that you might have thought was only for the toilet. (If you’re working with a bathroom sink, be sure to clog the overflow hole that’s near the top of the basin.)
Plunge it like you normally would a toilet—with a sink plunger of course. The next time you’re around a plunger, take a look at it. Does it have an extended part that goes beyond the dome shape? If so, that’s a toilet plunger—that extra three inches or so is to get deep down into the basin. If it’s just the dome/bowl, then you very well might be using a sink plunger to do a toilet plunger’s job. There is a difference, so take note.
If that doesn’t work, search for a clean-out plug on the main pipe. This handy opening (once unscrewed with a wrench) gives you access to the pipes without disassembly. Use a flexible, but tough brush to get in there and poke around to see if you can clear out any blockages (just be careful if you’ve already poured drain cleaners down the drain.)
Be sure to have a bucket on hand below the plug, though, as you don’t want any water splashing down on the floor while you impress everyone with your plumbing skills.
If you’re having some bad luck with the toilet and you find yourself without a plunger or if the plunger fails you, pour about a cup of dish detergent down there. It’ll act as a lubricant for the clog to wash down. You’ll need to let that work its magic for about 10 minutes. While you’re waiting, get a good amount of hot tap water, but not hot enough that it’s boiling. Pour it into the toilet bowl from an elevation (not so high as to splash clogged toilet water everywhere). Pour in the water so the whole mess will go down the drain.
5. Find A Stud Without A Stud Finder
If you find yourself on a weekend project with one of your buddies who wants to get his new flat-screen TV up on the wall, ask yourself two things: Will he let you come over to watch it, and does he know what the hell he’s doing?
In a perfect world, we’d be able to hang up heavy framed photos and flat screens anywhere we want on a wall for optimal viewing pleasure. But this is reality. And reality sometimes has you looking at bracketing on the floor and wondering what to do next.
Luckily, finding a stud – one of the most important things to know how to do as a beginner handyman – doesn’t require you going out and getting a device that looks very similar to a Taser and costs a pretty hefty amount for finding wood beams behind walls.
There are two ways to do this: an electric razor and a magnet. Sure you can knock on the drywall, but this is a gambling proposition without great odds.
For the razor or clippers. Turn it on and drag it flat across the wall. You should be able to hear a change in pitch. Keep in mind that studs are usually about 16 inches apart from one another, so you should be able to get a good idea of where each one is if you think you hear a tonal difference.
The more old-school method is to get a strong magnet attached to twine or thread and drag it along the wall. Since drywall is usually only a little more than a half inch thick at max, a powerful magnet can cling to any metal in the studs behind it.
FREE BONUS – Caulk Like A Pro
Caulking is an art form. The first step, as with most projects, is to make sure the surface you’re working on is clean. Use rubbing alcohol, this usually breaks down any oil or residue that could make the caulk not stick properly.
Next, use some tape on either side of the surface you’ll be caulking. This, like painters tape, will ensure straight, crisp lines.
Caulking is sort of like using a pastry bag (if you’ve done it). It requires constant pressure and the correct application, which is achieved by cutting the tip of your canister to a 45-degree angle. Insert the caulk into your gun—make sure you’ve punctured it if your gun doesn’t have a mechanism that does so for you – and take a deep breath.
Using constant pressure on the trigger, go between the taped lines. Don’t worry too much if it isn’t completely perfect, as you’ll be smoothing it out with your finger later, but get it as smooth as you can.
After you finish that up, wet your finger with some of that alcohol or some water and go along the caulked line, pushing it up against the surface while smoothing it out simultaneously. Wipe your finger as you go, as if you let your finger collect too much, it makes the job harder.
Once you’re done, pull off the tape and admire your slick work.